Thermal and hydraulic characteristics of a large-scaled parabolic trough solar field (PTSF) under cloud passages

To better understand the characteristics of a large-scaled parabolic trough solar field (PTSF) under cloud passages, a novel method which combines a closed-loop thermal hydraulic model (CLTHM) and cloud vector (CV) is developed. Besides, the CLTHM is established and validated based on a pilot plant. Moreover, some key parameters which are used to characterize a typical PTSF and CV are presented for further simulation. Furthermore, two sets of results simulated by the CLTHM are compared and discussed. One set deals with cloud passages by the CV, while the other by the traditionally distributed weather stations (DWSs). Because of considering the solar irradiance distribution in a more detailed and realistically way, compared with the distributed weather station (DWS) simulation, all essential parameters, such as the total flowrate, flow distribution, outlet temperature, thermal and exergetic efficiency, and exergetic destruction tend to be more precise and smoother in the CV simulation. For example, for the runner outlet temperature, which is the most crucial parameter for a running PTSF, the maximum relative error reaches −15% in the comparison. In addition, the mechanism of thermal and hydraulic unbalance caused by cloud passages are explained based on the simulation.     

高拱坝施工期温控参数敏感性分析

在混凝土高拱坝浇筑过程中,影响坝体施工期温度场及温度应力的因素有很多,因此选用适当的浇筑方案对于节约工程成本及提高坝体安全性有着重要意义。以孟底沟水电站工程为例,选用多种施工方案,并利用三维有限元方法进行仿真分析,分析了浇筑季节、浇筑层厚、间歇时间及浇筑温度等因素对坝体施工期的敏感性。结果表明,低温季节浇筑、在防止热量倒灌的前提下尽量减小浇筑层厚度、缩短间歇时间、降低浇筑温度有助于降低温度应力,提高坝体安全性。     

机械密封腔流场内粒子对密封腔壁面及波纹管冲蚀分析

为研究机械密封腔内混有固体颗粒的流体,在复杂工况下对密封腔壁面及波纹管表面冲蚀的影响,以CFD理论及方法,采用k-ε湍流模型和离散项DPM模型,对固液混合流场进行模拟分析,获得密封腔内流体中介质作用下密封腔壁面及波纹管外表面的压力场分布,分析不同工作状态下固体颗粒作用下密封腔内壁和波纹管外表面的冲蚀区域分布、固体颗粒在流场中的运动轨迹,以及机械密封工作过程中流场内固体颗粒的逃逸量、运动状态的变化。结果表明:粒子主要受颗粒阻力、浮重力、压力梯度力及波纹管和密封腔表面反作用力的影响;在旋转流场中,粒子作与旋转方向一致的螺旋方式前进;无转速时,冲蚀多发生在靠近入口处的波纹管外表面,旋转流场中,冲蚀多发生在密封腔靠后位置的壁面;随着转速增加,粒子逃逸率下降。研究结论为机械密封腔的设计布局及机械密封装置的优化提供理论依据。     

相场法模拟GaAs衬底上InGaAs异质结表面形貌

本工作采用相场法模拟GaAs衬底上生长的In_(0.3)Ga_(0.7)As多层异质结构薄膜表面。通过引入多序参量,使用半隐性傅里叶谱方法求解Cahn-Hilliard方程可以求得带缓冲层结构的薄膜表面形貌。计算结果模拟了薄膜生长过程,研究显示,使用In0.15-Ga0.85As缓冲层,厚度从1nm增加到4nm,薄膜表面临界波长从34nm提升到80nm。随着缓冲层的厚度从1nm增加到10nm,使用正弦波表面的模拟结果显示,薄膜表面粗糙度从2.87nm下降到0.43nm,随机叠加波表面的模拟结果也类似,表面粗糙度从1.21nm下降到0.18nm。热力学分析和应变分布分析可以解释缓冲层对薄膜表面形貌演化的作用。该模拟计算方式对设计缓冲层结构有很大的帮助,模拟计算的结果可以与实验相比对。     

New exact solutions of the Tzitzéica-type equations in non-linear optics using the expa function method

One specific class of non-linear evolution equations, known as the Tzitzéica-type equations, has received great attention from a group of researchers involved in non-linear science. In this article, new exact solutions of the Tzitzéica-type equations arising in non-linear optics, including the Tzitzéica, Dodd–Bullough–Mikhailov and Tzitzéica–Dodd–Bullough equations, are obtained using the exp_a function method. The integration technique actually suggests a useful and reliable method to extract new exact solutions of a wide range of non-linear evolution equations.     

The efficiency and comparison of novel techniques for cell wall disruption in astaxanthin extraction from Haematococcus pluvialis

The efficiency of various techniques pulsed electric field (PEF), ultrasound (US), high‐pressure microfluidisation (HPMF), hydrochloric acid (HCl) and ionic liquids (ILs) for cell wall disruption in astaxanthin extraction from Haematococcus pluvialis was compared. The results indicated that ILs, HCl and HPMF treatment were shown the most efficient for cell disruption with more than 80% astaxanthin recovery. While the cell wall integrity of H. pluvialis cyst cell was less affected by US and PEF treatment. It was found that imidazolium‐based ILs showed the greater potential for cell disruption than pyridinium‐based and ammonium‐based ILs. Among all the ILs examined, 1‐butyl‐3‐methylimidazolium chloride ([Bmim] Cl) exhibited efficient cell disruption and capability of astaxanthin recovery at mild condition (pretreatment with 40% IL aqueous solution at 40 °C, followed by extraction with methanol at 50 °C) without extensive energy consumption and special facility requirement. In addition, recyclability of ILs was excellent.     

基于翻领松量结构模型的翻折领结构设计方法

为解决翻领松量计算精准性及翻折领通用结构设计方法的问题,提出了一种基于翻领松量结构模型的翻折领结构设计方法。通过构建翻领松量结构模型确定了翻领松量计算系数,对6种不同状态下的翻领间隙量变化进行数据统计分析,依据翻领间隙回归系数模型确定了翻领松量计算给定常数,运用SPSS统计软件对实验数据进行了相关性分析、回归分析、配对样本T检验,并推导出翻领松量计算公式。实验结果表明:使用该公式计算的翻领松量提高了翻折领结构造型的准确性,基于翻领松量结构模型的翻折领结构设计方法可以满足不同翻折领领型结构设计要求。     

水下循迹航行器水动力学性能数值研究

为了研究低速水下循迹监测航行器的水动力学性能数值计算问题,采用FLUENT软件和SST剪切应力输运模型,通过雷诺时均N-S方程分析流速一定的情况下,取不同攻角、不同水平舵角作为来流条件,研究未安装推进器以及安装推进器且其安装位置不同时,航行器的升力系数、俯仰力矩系数、表面压力分布和流场速度的变化规律。结果表明:在未安装推进器以及推进器的安装位置不同时,随着攻角的变化,升力系数呈线性变化,俯仰力矩系数呈非线性变化;随着水平舵角的变化,升力系数和俯仰力矩系数呈线性变化。当推进器安装在航行器头部时,对航行器流场压力和流场速度变化影响最大;当安装在航行器尾部时,对二者影响最小。对于低速航行器,应尽量将推进器安装在中间靠后位置,以提高航行器的水动力性能。升力系数的试验结果与数值仿真结果之间最大相差7. 51%,阻力系数的试验结果与数值仿真结果最大相差5. 84%,均吻合较好。研究结果可以为低速水下循迹航行器的优化设计和发展提供理论参考。     

激光立体成形TC4钛合金的热力场演化

激光立体成形能够实现高性能复杂零件的精确成形，但成形过程中的高温度梯度极易导致残余应力和变形，最终影响构件的几何精度和力学性能。通过搭建基板单边夹持原位热变形测量系统，探究了多道多层TC4钛合金成形件在激光立体成形过程中基板温度、变形的演化规律，分析了不同扫描策略对构件热应力场的影响。研究结果表明，构件的变形发展受其热历史驱使，扫描策略对成形件的热变形具有显著影响。     

发夹式换热器管束流致振动数值模拟研究

运用计算流体力学方法,采用ANSYS CFX软件对发夹式换热器的壳侧流场进行了三维数值模拟。流场计算中采用多孔介质模型对管束区域进行简化,分析了壳侧流场的速度分布,结果表明:直管段部分的流体湍流强度大于弯管段,且外层管束所在区域为高流速区,受流体冲刷严重。结合流场信息,通过功率谱生成随机激振力,采用ABAQUS软件模拟计算了湍流激振下管束的振动响应,结果显示管束的面外均方根位移远大于面内位移,且弯管部分的振动位移最大。该研究结果可为发夹式换热器的性能分析和优化设计提供参考和依据。